CITJobs In Automation
Guide

Servo Drive Troubleshooting: Motion Control Basics for Techs

What an automation technician actually needs to know about servo motors, drives, encoders and motion instructions to keep an axis running and find the fault fast.

Jobs In Automation Editorial9 min read

Key takeaways

  • A servo axis is three parts working as one: motor, drive and feedback device. Most faults trace to one of the cables between them, not the electronics.
  • Position error (following error) faults are the most common servo trip, and the usual causes are mechanical binding, a feedback problem or a load change the tuning no longer fits.
  • Know your feedback type. Incremental encoders lose position at power-down, absolute encoders do not, and battery-backed absolute encoders need re-homing when the battery dies.
  • Traditional guidance keeps load-to-motor inertia ratio under 10:1. A machine that was retooled with a heavier load may need retuning, not a new motor.
  • PLCopen motion blocks (MC_Power, MC_Home, MC_MoveAbsolute) give you one mental model that carries across many controller brands.

Servo drive troubleshooting is where a lot of automation technicians either earn a reputation or lose one. A conveyor motor on a VFD will forgive a lot. A servo axis on a pick-and-place, a flying cutoff or a packaging machine will not. It faults, it stops the line, and everyone looks at the person with the laptop.

This guide covers the motion control basics that matter on the floor: what is in a servo system, how the feedback works, what tuning really means, how to read the most common faults, and where the PLC side fits. It assumes you already know basic ladder logic and can use a meter safely. If not, start with our PLC programming basics piece first.

What Is Actually in a Servo System

Every servo axis has three core pieces: the motor, the drive (amplifier) and a feedback device, usually an encoder or resolver mounted on the motor. The controller commands a position or velocity, the drive pushes current into the motor, and the feedback device reports where the shaft really is. The drive compares the two continuously and corrects the difference.

That loop is the whole point. As Control Design explains, a servo is a closed-loop system: the controller keeps checking commanded position against measured position and adjusts motor current to close the gap.

A few physical details matter for troubleshooting:

  • Two cables, not one. Servo motors usually run a power cable and a separate feedback cable. Brake and motor temperature signals sometimes ride in the feedback or control cable, so a damaged feedback cable can show up as a brake or overtemperature fault.
  • Matched sets. Motors and drives are often specified as a set from the same manufacturer because the drive needs the motor's electrical data to control it well. Swapping in a different motor is rarely plug-and-play.
  • Holding torque at zero speed. Unlike an induction motor on a VFD, an enabled servo actively holds position. Push the load off position and the drive fights back, and if it cannot recover it faults.
  • A network, not just wires. Modern drives talk to the controller over a fast dedicated network, typically industrial Ethernet. Rockwell's ControlLogix 5590, for example, supports integrated motion over EtherNet/IP or Sercos and up to 512 axes per controller.

Those points come straight from the Control Engineering motion troubleshooting guide, which also makes the point every senior tech repeats: read the documentation for the platform in front of you.

Servo vs. Stepper vs. VFD: Know Which One You Are Looking At

New techs sometimes treat every motor with a drive the same way. They are not the same, and the troubleshooting approach differs.

Drive typeFeedbackWhere you see itWhat tends to go wrong
StepperOften none (open loop)Constant, predictable loads: small indexers, diverters, x-y tablesLost position under unexpected load, since nothing tells the controller; torque falls off at higher speed
ServoEncoder or resolver (closed loop)Dynamic loads, precise positioning, synchronized axes, robotsFeedback faults, position error trips, tuning drift after mechanical changes
VFD on induction motorUsually none; sometimes an encoder for speed or indexingPumps, fans, conveyors, mixersOvercurrent, overvoltage on decel, motor and cable insulation problems

Control Design notes that stepper performance starts to fall off above about 1,000 rpm and that a servo system can cost up to three times as much as a comparable stepper. That is why machine builders still use steppers where the load is steady. It also tells you something when you troubleshoot: if a stepper axis is losing position, the motor may be undersized for a load that changed, and there is no encoder to tell you so.

Encoders, Resolvers and Feedback Types

Most servo faults you will chase involve feedback. Knowing what type of device is on the motor tells you what failure looks like and what recovery requires. KEB America's feedback overview breaks the common types down like this:

  • Incremental encoders put out A and B pulse channels (offset so the drive can tell direction) plus a Z or index pulse once per revolution. Common signal levels are 5 V TTL and 24 V HTL. They lose absolute position when power drops, so the axis must home after every power-up.
  • Absolute encoders report a unique position value. Single-turn versions know where they are within one revolution. Multi-turn versions also count revolutions, so the machine knows its position at power-up without homing.
  • Resolvers are rugged transformer-style devices that output sine and cosine signals. They handle heat and vibration well but are not the choice when top precision matters.
  • Sin/cos and serial encoders such as Hiperface, EnDat and BiSS give high resolution and can carry diagnostic data. BiSS is an open interface; Hiperface and EnDat are proprietary. KEB notes that high data rates can limit how long the encoder cable may be.
Battery-backed absolute encoders: Many multi-turn absolute encoders keep their turn count with a backup battery. When that battery dies or is disconnected, the axis loses its reference and must be re-homed or re-referenced. One trade publication puts typical battery life at three to four years. If a machine throws an absolute-position alarm after a long shutdown or a motor swap, check the battery before you suspect the encoder.

Cable length, shielding and connector condition matter more on feedback than on power. A feedback cable flexing in a cable track for years is a classic intermittent fault: the axis trips only at one end of travel, or only when the track bends a certain way.

Servo Tuning Basics: The Three Loops

You do not need to be a controls engineer to understand tuning, but you should know what the gains do so you can tell when tuning is the problem.

A servo drive runs three nested loops. The current (torque) loop is innermost and fastest. Around it sits the velocity loop, and around that the position loop, which is the slowest. According to Advanced Motion Controls, each outer loop depends on the one inside it performing well, and pushing for higher bandwidth means higher gains and a greater risk of instability.

On the floor, that translates into a few patterns:

  • Gains too low: the axis is sluggish, overshoots slowly, or trips on following error during fast moves because it cannot keep up.
  • Gains too high: the axis buzzes, hums or oscillates at standstill, and you may hear it sing.
  • Load changed: a new tool, a heavier product or a different gearbox changes the inertia the drive sees. Tuning that was fine last month may no longer fit.

Inertia ratio is the number to know here. The A3 glossary defines it as load inertia reflected to the motor shaft divided by motor rotor inertia. Traditional guidance keeps it under 10:1. A3 notes that modern drives can handle around 30:1 or more with careful tuning, while 1:1 to 3:1 gives the snappiest response. Most drives have an auto-tune or inertia-estimation routine. Use it with the machine safe, the axis clear and the supervisor's okay, and save the old parameters first.

Servo Drive Troubleshooting: Common Faults and Where to Look

Fault names differ by brand, but the underlying causes repeat. Aerotech's documentation on its position error fault is a good model because it splits causes by situation. A new axis that faults on its first move usually has a configuration, wiring or phasing problem, or a shipping clamp still installed. An axis that ran fine for years and now faults on every move points toward a failed feedback device, damaged cable, mechanical damage or a brake that is not releasing.

SymptomCheck firstThen check
Position or following error faultMechanical binding, jammed product, brake not releasingFeedback cable and connectors; load change since last tune
Fault only on fast or long movesDrive at current limit; bus voltage sagSpeed or accel set beyond motor capability; tuning
Encoder or feedback faultFeedback connector seated, cable damage in trackShield grounding, noise from routing next to power cables
Absolute position lost after power-offEncoder backup batteryRe-reference procedure in the drive manual
Axis hums or oscillates at standstillGains too high, loose couplingMechanical resonance, worn belt or gearbox
Axis will not enableSafety circuit (STO) open, drive ready signalController axis state, fault not reset

One check catches a lot: with the drive disabled and the axis safe to move, turn it by hand and watch the position value in the software. If the number does not change, you have a feedback problem. If it changes smoothly but the axis still faults under power, look at the motor, brake, mechanics or tuning. And do not forget couplings. Control Engineering specifically calls out mechanical parts like couplings as wear items that belong in routine checks.

Motion on the PLC Side: PLCopen and Axis States

The other half of motion control lives in the controller program. Here the most useful thing to learn is the PLCopen motion model, because many controller vendors base their motion instructions on it even when the names differ.

The PLCopen motion control overview defines a state machine every axis follows: Disabled, Standstill, Homing, Discrete Motion, Continuous Motion, Synchronized Motion, Stopping and ErrorStop. Standard function blocks move the axis between states, for example MC_Power to enable, MC_Home to home, MC_MoveAbsolute and MC_MoveRelative for point-to-point moves, MC_Stop and MC_Halt to stop, and MC_Reset to clear an error.

Why this helps a technician: when an axis will not move, ask what state it is in. An axis in ErrorStop will ignore every move command until it is reset. An axis that never left Disabled has a power or enable problem. Rockwell, Siemens, Beckhoff and others have their own instruction names, but the logic of the state machine is the same idea, so the habit transfers.

How to Build Motion Control Skills as a Technician

Motion work rewards hands-on time more than reading. A practical path:

  1. Learn one drive family deeply. Pick whatever your plant runs most and learn its software well enough to view feedback, read fault history, back up parameters and run auto-tune.
  2. Back up before you touch. Save drive parameters and the controller program before any change. Restoring a known-good file is the fastest fix there is.
  3. Trace one axis end to end. Follow the schematic from the safety circuit to the drive enable, through the power and feedback cables, to the controller instructions that move it.
  4. Use training rigs. Vendors like Festo sell servo and stepper training setups built around a linear axis, which let you practice position, speed and torque control without risking a production machine.
  5. Watch an experienced tech tune. Ask them what they look at on the trend and why.

A3 runs a Certified Motion Control Professional program aimed at people who integrate, build or maintain automated equipment. It is worth a look once you have the basics, though a certificate matters less than being the person who can get a faulted axis running again. For broader credentials, see our guide to robot-specific certifications.

Bottom Line

You do not need to design motion systems to be valuable around them. You need to know what kind of feedback is on the motor, what the three tuning loops do, how to read a position error fault, and what state the axis is in on the controller side. Learn one drive platform well, always back up before you change anything, and check the mechanics and the feedback cable before you blame the electronics. Techs who can do that are the ones plants call when the fastest machine on the floor goes down.

Frequently asked questions

What is the difference between a servo motor and a stepper motor?

A servo motor runs closed loop: an encoder or resolver reports actual position and the drive corrects any error. Many stepper systems run open loop with no feedback, so they cannot detect a missed position. Steppers are cheaper and work well for steady loads, while servos handle changing loads, higher speeds and precise synchronized motion.

What causes a servo position error or following error fault?

The drive trips when the gap between commanded and actual position exceeds a set limit. Common causes are mechanical binding, a brake that is not releasing, a damaged feedback cable, a failed encoder, the drive hitting its current limit, low bus voltage, or tuning that no longer suits the load after a mechanical change.

Why does a servo need to be homed after power loss?

Incremental encoders only count pulses, so they lose the axis position when power is removed and the machine must home to find a reference. Multi-turn absolute encoders keep position through power cycles, but many use a backup battery to do so. If that battery dies, the axis has to be re-referenced.

What is a good inertia ratio for a servo?

Traditional guidance keeps the ratio of load inertia to motor inertia under about 10:1. Ratios of 1:1 to 3:1 give the fastest response. Modern drives with advanced control can handle higher ratios, roughly 30:1 or more, but they need more careful tuning to stay stable.

Looking for automation work?

Tell us your trade, location and experience. The Careers In Trades network routes you to employers who are actually hiring. Free for workers.

Sources

  1. Control Engineering — Motion control and robotics troubleshooting and maintenance advice
  2. KEB America — Introduction to feedback devices for VFD and servo applications
  3. Control Design — Are servo and stepper functionalities merging?
  4. Advanced Motion Controls — What is servo bandwidth
  5. A3 — Inertia matching (glossary)
  6. Aerotech Automation1 Help — Position Error Fault
  7. PLCopen — Motion control overview
  8. Fierce Electronics — Battery-free multi-turn absolute encoder boosts servo system performance

Pay, licensing and program details change and vary by state, employer and local agreement. Verify with the linked sources and your state licensing board before making decisions.